|
Verify Alignment |
Verify alignment on printer P7. (I G N R E C) |
| |
-
I -- To
continue printing aligned forms starting with the
next line of the file.
-
G -- To
continue printing aligned forms skipping to the next
form and printing the first line again, type a G.
-
N -- To
print the first line again on the next form and to
verify the alignment,
- R -- To print the first line
again on the current form and to verify the
alignment if the forms are not aligned,
- E -- To eject a page and print
the first line again,
- C -- To cancel processing, type a
C.
|
Message ID . . . . . .
: CPA4002 Severity . . . . . . . : 99
Message type . . . . . : Inquiry
Date sent . . . . . . : 05/28/07 Time sent . . . . .
. : 15:34:57
Message . . . . : Verify alignment on printer P7. (I
G N R E C)
Cause . . . . . : The forms may not be aligned
correctly. The first line
for the file is 1.
Possible choices for replying to message . . . . . . . .
. . . . . . . :
I -- To continue printing aligned forms starting with
the next line of the
file, type an I.
G -- To continue printing aligned forms skipping to the
next form and
printing the first line again, type a G.
N -- To print the first line again on the next form and
to verify the
alignment,
1. Press Stop only if Start and Stop are two keys, or
press Reset.
2. Advance the paper to the next form by pressing Form
Feed/New Page.
3. Adjust the alignment with the forms adjust control.
4. Press Ready, Start, or Start/Stop.
5. Type an N.
R -- To print the first line again on the current form
and to verify the
alignment if the forms are not aligned,
1. Press Stop only if Start and Stop are two keys, or
press Reset.
2. Adjust the alignment with the forms adjust control.
3. Press Ready, Start, or Start/Stop.
4. Type an R.
E -- To eject a page and print the first line again,
1. Press Stop only if Start and Stop are two keys, or
press Reset.
2. Adjust the alignment with the forms adjust control.
3. Press Ready, Start, or Start/Stop.
4. Type an E.
C -- To cancel processing, type a C.
[back to top]
|
|
End of Forms |
End
of forms or forms jam on device P1 |
| |
- Load new forms
- Clear any jam
- Press start stop
|
Message ID . . . . . .
: CPI4020 Severity . . . . . . . : 99
Message type . . . . . : Information
Date sent . . . . . . : 06/15/07 Time sent . . . . .
. : 17:01:13
Message . . . . : End of forms or forms jam on device
P1.
Cause . . . . . : Either an end of forms or a forms jam
has caused the
printer to stop printing file QPSPLPRT in library QSYS.
Recovery . . . : Either load new forms or clear the
forms jam. Then press
Ready or press Start to continue printing.
[back to top]
|
|
Forms Jam |
End
of forms or forms jam on device P1 |
| |
- Load new forms
- Clear any jam
- Press start stop
|
Message ID . . . . . .
: CPI4020 Severity . . . . . . . : 99
Message type . . . . . : Information
Date sent . . . . . . : 06/15/07 Time sent . . . . .
. : 17:01:13
Message . . . . : End of forms or forms jam on device
P1.
Cause . . . . . : Either an end of forms or a forms jam
has caused the
printer to stop printing file QPSPLPRT in library QSYS.
Recovery . . . : Either load new forms or clear the
forms jam. Then press
Ready or press Start to continue printing.
[back to top] |
| |
|
|
Press Start/Stop |
Press Ready, Start/Stop on printer |
| |
- Press start stop. The
printer is currently offline
|
|
[back to top]
|
|
Started Printer |
This
file is not associated with a started printer |
| |
- type a '9' work with printing
status beside the file then press ENTER
- type a '2' to work with printing
status then press ENTER (see figure 1)
- press enter on the printer id
that you want to start (see figure 2)
- the printer should start
|
|
Figure 1
Figure 2
[back to top] |
| |
|
|
Printer won't print |
Printer won't printer no matter what I do |
| |
|
|
[back to top] |
| |
|
|
Another common message is Press Ready, Start/Stop on printer.
☞ If this message appears check to see if one Green light is off or blinking.
☞ Correct this by pressing the green (Start/Stop or Ready) button. Once you see
TWO green lights (i.e. Power & Ready) you are ready to print.
☞ Next, press the ENTER key to continue to the previous menu.
5. Exit the Work with Output Queue menu by pressing the Cmd3 (Exit) key. You
will be returned to your previous menu.
How to print part of a Spool File
☞ Periodically you may need to print part of a large document or spool file. You
can only do this if the spool file is still in the output queue (i.e., it was
saved after printing or has not yet printed). To print part of a spool file:
1. WRKOUTQ P[printer ID].
2. Select Option “2” (Change) the spool file and press ENTER.
3. Press the Cmd10 (More Options) key.
4. Scroll down one page (Shift + Up Arrow on Terminals or Page Down on PCS) to
the PAGERANGE parameter.
Key the number of the first page you want to print in the START PAGE field and
the last page you want to print in the ENDING PAGE field.
4. Select SAVE(*YES) to save the spooled file. Otherwise, it is lost after it
finishes printing. If it hasn’t finished printing, then you can still select
SAVE(*YES) for any Spool file that is currently writing or held.
5. Press the ENTER key. The spool file will reprint, beginning and ending with
the page number(s) you indicated.
|
